Process parameters influence on zone refining and thermodynamics analysis of 1,2-diphenylethane

Effective distribution coefficients of 9 impurities in 1,2-diphenylethane have been calculated by directional crystallization under different ambient frozen temperature. The effect of varied zone size, temperature difference between the melt and ambient frozen environment, number of zone on purity of 1,2-diphenylethane have been also investigated during the process of zone refining. The results indicate that the product purity in the intermediate purified region with varied zone size is higher 0.04%-0.2% than that with constant zone size. The product purity increases with temperature difference between the melt and ambient frozen environment. The appropriate temperature difference is adopted 50℃. The product purity in the intermediate region of sample bar with 2 molten zones is higher 0.05%-0.43% than that with 1 molten zone. In addition, the change of enthalpy and entropy between impurities and 1,2-diphenylethane have been determined.     

Investigation of the Ga-Sb-S chalcogenide glass with low thermo-optic coefficient as an acousto-optic material

In this study, two series of Ga_xSb_40-xS₆₀ (x = 4, 6, 8, 10 mol%) and Ga_ySb₃₆S_64-y (y = 3, 5, 6 mol%) glasses were prepared and the relationship between their compositional and acousto-optic (AO) properties was investigated systematically for the first time. In the Ga_ySb₃₆S_64-y system, the AO figure of merit (M₂) increased as the Ga increased, and the maximum M₂ of the Ga₆Sb₃₆S₅₈ glass was 455.78 × 10^?18 s³/g, which is ～301 times greater than that of fused silica and ～2.5 times greater than that of As₂S₃ chalcogenide (ChG) glass at 1550 nm. However, its thermo-optic coefficients (dn/dT) varied greatly (32.1 × 10^?6 °C^?1–57.2 × 10^?6 °C^?1), and acoustic attenuations (α) at 10 MHz were high, from 5.446 dB/cm to 7.274 dB/cm. In the Ga_xSb_40-xS₆₀ glass system, the M₂ value and α at different ultrasonic frequencies gradually decreased with the improvement of Ga. Compared with the Ga_ySb₃₆S_64-y system, the Ga_xSb_40-xS₆₀ glass system had lower α (at 10 MHz) and dn/dT, which are 5.001 dB/cm–5.563 dB/cm and 17.3 × 10^?6 °C^?1–55.6 × 10^?6 °C^?1, respectively. These results provide a significant reference for the further development of novel ChG glasses and help expand their application fields.     

Wear resistance and hardness properties of TiB2– Fe coating developed on AISI 1020 steel by tungsten inert gas (TIG) cladding

The present work is attempted to improve the microhardness and wear properties of AISI 1020 steel by depositing TiB₂–Fe composite coating using tungsten inert gas (TIG) cladding. In this study, different compositions of TiB₂–Fe paste form were preplaced on the substrate plates and then TIG heat input was applied to deposit hard composite coating layer. The main objective of the present work was to explore the influence of TIG input current as well as iron content on the microstructure and surface properties of deposited coatings. Microhardness, microstructural and phase characterization of the coating have been done by the Vickers microhardness tester, scanning electron microscope (SEM), Energy dispersive spectroscopy (EDS) and X-ray diffractrometer (XRD). The results showed that the microhardness of the TiB₂–Fe coating was strongly influenced by the composition of the coating materials as well as the TIG processing current. The microhardness increases with decreasing Fe contents in the coating materials with constant processing current (90 A) as well as it also increases with decreasing processing current with the fixed composition of coating materials (80TiB₂–20Fe). The maximum average microhardness found was 3082 HV_0.1 for the coating of 100TiB₂–0Fe composition ratio and 90 A processing current which was about 18 times higher than that of the substrate average microhardness value (163 HV_0.1). Average wear rate evaluated by considering weight loss of the TIG cladded samples using pin on disc tribometer by the sliding distance of 864 m and 20 N normal loads. The wear results also showed that the coating contains 100 wt% of TiB₂ (0 wt% of Fe) exhibited lower rate of wear 6.74 × 10^?8 g/Nm which is about 24 times lower as compared to AISI 1020 mild steel wear rate (166.31 × 10^?8 g/Nm).     

基于归一化水体指数及其阈值自适应算法的水体遥感反演效果分析

归一化水体指数（NDWI）是水体遥感反演的一种重要指标，其阈值及修正直接影响反演结果的精度。基于Landsat-8与GF-1光学多光谱影像，使用归一化水体指数法阈值0（TH₀）、最大类间方差法（OTSU）自适应阈值（TH_otsu）与均值漂移聚类算法（Mean-Shift）自适应阈值（TH_MS）分别对典型正常水体、云雾覆盖水体、富营养化水体、高含泥沙水体进行水体遥感提取与效果分析，结果表明：正常水体以TH₀为阈值提取精度最高，THMS提取精度次之，TH_otsu提取精度最差；而云雾覆盖水体、富营养化水体以及含泥沙水体使用THMS提取精度最高，尤其少量云雾覆盖下的水体，TH_MS具有更明显的优势，TH₀提取精度次之，TH_otsu提取精度最差；对于不同的阈值，Land?sat-8比GF-1总体表现出更高的水体提取精度。Mean-Shift算法应用于NDWI阈值修正与水体遥感反演具有快速、水质适应性强、效果稳定的优势，对尤其是复杂条件下的水体信息遥感反演具有较好的提取效果。     

提升管内颗粒浓度梯度力的特性

由于Kutta-Joukowski横向力与浓度梯度力的共同作用，提升管内颗粒沿径向在边壁大量聚集并形成稳定的环?核结构。根据实验数据，分析了颗粒浓度梯度的径向分布特征，考察了不同操作条件下浓度梯度力系数K的分布特性。由Kutta-Joukowski横向力与浓度梯度的关系，提出了浓度梯度力的表达式Fρ=K(dρ/dr)A及浓度梯度力系数K的表达式K=[?ρg(νg?νp)(?v/?r)r]/?dρ/dr+(d2ρ/dr2)r?。提升管内颗粒群受到的浓度梯度力与浓度梯度力系数K有关。浓度梯度力系数K在提升管中心处为0，沿提升管径向呈“N”型分布，随表观气速增加而增加；提升管内充分发展段K的数值明显大于提升管加速区和出口约束区，总结了浓度梯度力系数K的经验关联式。     

镁合金网格壁板压弯成形数值模拟及实验研究

为探索镁合金整体壁板压弯成形的可行性,以及镁合金壁板压弯成形过程中金属的流动规律,对AZ31镁合金网格壁板压弯成形进行了数值模拟和实验研究。建立了有限元数值模拟的几何模型,采用有限元计算软件对AZ31镁合金网格壁板压弯成形过程进行了数值模拟研究,分析了镁合金网格壁板压弯成形中的温度场、应变场、应力场、破坏系数等的分布规律。确定了合适的AZ31镁合金壁板压弯成形工艺参数,并对镁合金网格壁板压弯成形进行了实验研究,获得了合格的镁合金网格壁板弯曲件,并分析了镁合金网格壁板成形件尺寸精度,模拟结果与实验结果相吻合,最大相对误差为16.7%。     

聚类混合型数据的密度峰值改进算法

聚类混合型数据，通常是依据样本属性类别的不同分别进行评价。但这种将样本属性划分到不同子空间中分别度量的方式，割裂了样本属性原有的统一性；导致对样本个体的相似性评价产生了非一致的度量偏差。针对这一问题，提出以二进制编码样本属性，再由海明差异对属性编码施行统一度量的新的聚类算法。新算法通过在统一的框架内对混合型数据实施相似性度量，避免了对样本属性的切割，在此基础上又根据不同属性的性质赋予其不同的权重，并以此评价样本个体之间的相似程度。实验结果表明，新算法能够有效地聚类混合型数据；与已有的其他聚类算法相比较，表现出更好的聚类准确率及稳定性。     

纵轴式掘进机截割头载荷影响因素的仿真分析

针对现有掘进机截割头载荷特性研究方法采用单一影响因素不能全面反映截割头载荷及其波动变化规律的问题,通过分析截割头瞬时载荷,确定了纵轴式掘进机在水平截割工况下截割头载荷的主要影响因素有截割岩石特性、截割头掏槽深度、截割头吃刀深度、截割头转速和截割臂摆速。针对某纵轴式掘进机水平截割工况,采用Matlab对影响截割头载荷的多种因素进行仿真分析,得到了各向载荷及其波动随各因素的变化规律:截割头载荷随着岩壁普氏系数的增大而增加,其中横向阻力增加尤为明显,横向阻力波动程度高于其他方向载荷,且随着岩壁普氏系数的增大呈减小趋势;随着截割头掏槽深度的增加,截割头各向载荷近似呈线性增加,其中升力增加幅度最大,各向载荷波动则随着截割头掏槽深度的增大而减小;随着吃刀深度的增加,截割头载荷总体呈增大趋势,载荷波动程度则随之减小;在截割头转速一定的情况下,截割头载荷均随着截割臂摆速的增加而增大,在同一摆速下,截割头载荷随着截割头转速的减小而增大,横向阻力波动明显高于升力和推进阻力波动,横向阻力和推进阻力波动按截割头载荷规律变化,升力波动则与之相反。截割头载荷波动变化规律与截割头载荷变化规律不尽一致,有时甚至相互冲突。因此,掘进机作业过程中应合理选择截割头掏槽深度、吃刀深度等操作参数和截割头转速、截割臂摆速等运动参数,使各参数相互匹配,以减小掘进机振动,延长使用寿命。     

Analysis and assessment of a nanoparticle seeded small scale absorption refrigeration system driven by a low‐grade waste heat source

The thermoeconomic behaviour of a nanoparticle seeded single effect LiBr‐H₂O absorption refrigeration system (ARS) is investigated for a small scale application. In the proposed method, alumina nanoparticles with volume concentrations of 3%, 5%, and 7% are dispersed into an aqua lithium bromide solution. The multiobjective heat transfer search algorithm is employed to examine the design trade‐off between the coefficient of performance (COP) and total annualized cost (TAC). To analyze the overall performance of the system, the influence of five design parameters, namely the temperatures of the generator, absorber, evaporator, condenser and heat exchanger pipe diameter, are studied. It is found that with an increase in the COP, the TAC of the system is initially raised marginally, and after that, raised rigorously with further increment. The comparative results indicate that the COP and TAC of the nanofluid based ARS system are increased by about 7% and decreased by about 3.2%, respectively, corresponding to the Pareto points of the base ARS system. A lower break‐even point of about 2.6 years is achieved for the ARS system containing nanoparticles compared to the base ARS system. Overall, the ARS system containing 5% nanoparticles is the best solution from a thermodynamic and economic point of view.     

A comparative study for consistency-based decision making with interval multiplicative preference relations

ABSTRACT

To ensure the reasonable application and perfect the theory of decision making with interval multiplicative preference relations (IMPRs), this paper continues to discuss decision making with IMPRs. After reviewing previous consistency concepts for IMPRs, we find that Krej?í’s consistency concept is more flexible and natural than others. However, it is insufficient to address IMPRs only using this concept. Considering this fact, this paper researches inconsistent and incomplete IMPRs that are usually encountered. First, programming models for addressing inconsistent and incomplete IMPRs are constructed. Then, this paper studies the consensus of individual IMPRs and defines a consensus index using the defined correlation coefficient. When the consensus requirement does not satisfy requirement, a programming model for improving consensus level is built, which can ensure the consistency. Subsequently, a procedure for group decision making with IMPRs is offered, and associated examples are provided to specifically show the application of main theoretical results.